User Stories

GasTOPS Develops and Tests Propulsion Control Algorithms for the USS Makin Island

View PDF

The USS Makin Island
The USS Makin Island.

“We mitigate risk by simulating complex marine and aircraft systems before they are built. To reduce costs, we automate simulations with MATLAB and reuse models throughout development. Understanding multidomain systems through simulations in Simulink and SimPowerSystems is invaluable to our business.”

Shaun Horning, GasTOPS

The USS Makin Island (LHD 8) is a twin-shaft amphibious assault ship in active service with the U.S. Navy. Nearly 850 feet long and with a full displacement of over 40,000 tons, the Makin Island can carry and launch dozens of helicopters and landing craft. Unlike earlier steam-powered ships of its class, the Makin Island uses a hybrid-electric propulsion system with gas turbines for high-speed travel and electric motors for efficient low-speed operation. The new propulsion configuration has two 35,000 BHP gas turbines, two 5000 BHP AC electric motors, and six diesel generators.

GasTOPS used Model-Based Design with MATLAB® and Simulink® to model the LHD 8 propulsion plant and develop its control algorithms, simulate the electrical power generation and distribution system, and create a simulator-stimulator system for real-time hardware-in-the-loop (HIL) testing of the machinery control system. This approach enabled the team to identify potential problems before sea trials began.

“With MATLAB and Simulink, we can rectify issues early in the design phase,” says Shaun Horning, vice president of Technical & Engineering Services at GasTOPS. “Before the ship is built, we can analyze crash astern, crash ahead, and other maneuvers, and generate a set of expected results to compare with actual sea trial results.”

Challenge

The machinery control system (MCS) aboard the LHD 8 controls the propulsion system, including transitions between electric motor and gas turbine drive modes, as well as more than 20 other major ship systems. Altogether, the MCS has more than 10,000 input and output signals.

To develop control algorithms for the complex, first-of-its-kind propulsion system, GasTOPS needed an accurate model of the plant. Later, GasTOPS would need to run parametric studies, model electrical power generation and distribution, generate code for HIL test setups, and create a simulation engine for an onboard training system. GasTOPS required a flexible, multidomain modeling and simulation environment that supported all these activities.

Solution

GasTOPS used Model-Based Design with MATLAB and Simulink to accelerate LHD 8 development and analysis projects. GasTOPS engineers developed a Simulink model of the propulsion system, including submodels for the hull, propellers, shafting, gearboxes, motors, generators, and gas turbines.

Many of these submodels came from a Simulink library of parameterized components that GasTOPS had developed for similar projects. Others were provided by OEMs as MATLAB or Fortran code, and integrated into the Simulink propulsion model.

GasTOPS modeled the machinery control system in Simulink and Stateflow®, using state transition diagrams to describe drive mode changeovers.

The engineers conducted an extensive test program in which MATLAB scripts were used to launch Simulink and collect the results of simulated ship maneuvers under various environmental conditions. In parametric studies, sweeps of propeller efficiency, hull resistance, and other key values were conducted to assess MCS performance and robustness.

For the electrical plant, the team used Simulink and SimPowerSystems™ to model six diesel generators, eight transformers, numerous smart breakers, and the distribution system, as well as electric motors and other loads. They performed simulations to evaluate the system response to short circuits, generator failures, and various fault conditions.

GasTOPS combined elements of the propulsion and electric plant models with models of other machinery systems in Simulink, and used Simulink Coder™ to generate code for a real-time HIL testing setup. They streamlined this process by creating MATLAB functions that generate Simulink models based on predefined operating parameters for pumps, valves, fans, and other components.

Later, the team extended the MCS test model to support simulation of about 100 different system and component faults, and used Simulink Coder to generate C code for an onboard training system.

The MCS is now in service aboard the USS Makin Island.

Results

  • Time-to-simulation cut by two-thirds. “It’s not uncommon for companies to spend six months or more modeling ships and other complex systems before they get any useful simulation results,” says Horning. “Using MATLAB and Simulink with the library and scripts we have developed, we can have simulation results in two months or less, which can be a huge advantage during the design process.”
  • Key design issues identified early. “Our simulations revealed that in the transition from turbine power to electric power, the turbines provided substantially more power than was expected during their cool down,” explains Horning. “Simulink enabled us—and our clients—to understand how the systems would perform before the ship was built.”
  • Models reused multiple times. “Our propulsion and electrical system models were based on Simulink library elements,” says Horning. “We reused elements of those models extensively to verify the controller design, generate code for HIL tests, and create the core of the onboard training environment.”

Challenge

Develop the propulsion control algorithms for the USS Makin Island

Solution

Use Model-Based Design with MATLAB and Simulink to model the ship’s main systems, develop and verify control algorithms, and generate code for onboard training and HIL test setups

Results

  • Time-to-simulation cut by two-thirds
  • Key design issues identified early
  • Models reused multiple times

Products Used

Learn more about GasTOPS